SAFE OPERATING PROCEDURE ANGLE GRINDER DO NOT use this equipment unless you have been instructed in its safe use and operation and given prior permission. PERSONAL PROTECTIVE EQUIPMENT PRE-OPERATIONAL SAFETY CHECKS Read Operators Manual and Risk assessment. Keep work area clean and tidy. Use only in designated grinding area – erect screens if ...
SAFETY OPERATING PROCEDURES Angle Grinder (Portable Equipment) DO NOT use this power tool unless you have received instruction in its safe use and operation and have permission. Safety glasses must be worn at all times in work areas. Long and loose hair must be contained. CSA approved footwear with substantial uppers must be worn.
Die grinders are a special version of end grinders to be used with mounted wheels or accessories 2" or less in diameter. Due to the small accessory diameters, die grinders are designed to work without a guard, therefore requiring a special attention while operating. You must have athorough understanding of all procedures for each job you perform.
Cutting and Grinding Safety. ... The angle grinder runs on for approximately 5 seconds after switch-off. ... Kickback results from tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking the following precautions: Maintain a firm grip with both hands on the unit and position your body and arms to allow you ...
Safety Policy and Procedure) and hands on for each type of grinder to be used. 7.3.2 Send training records to the Cianbro Training Institute; scan and email them to [email protected] 7.4 Tool Inspection 7.4.1 Inspect the cord and pneumatic fitting 7.4.2 All guards in …
Safe Operating Procedure (Revised 3/12) ABRASIVE WHEELS/GRINDERS – BENCH, FLOOR, AND HAND _____ (For assistance, please contact EHS at (402) 472-4925, or visit our web site at ... grinder, and that the type of wheel is compatible with the material being ground. An
Bench Grinder Safety OSHA 29 CFR 1910.215 for grinders is one of the most frequently cited machine-safety standards for violations during OSHA machine-safety inspections. This is due to improperly adjusted work rests and tongues on bench grinders. According to 29 CFR 1910.215(a)(4), work rests must be kept adjusted closely to the wheel with a ...
This manual is provided by WMH Tool Group covering the safe operation and maintenance procedures for a JET Model JPSG-618M1 Surface Grinder. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions …
Bench Grinder Operating Procedures 1. Inspect & Adjust Grinder Ensure area around grinder is clean and well maintained. Side guard must cover the spindle, nut …
Operating this Stump Grinder safely is necessary to prevent or minimize the risk of death or serious injury. Unsafe operation can create a number of hazards for you. Always take the following precautions when operating this Stump Grinder: Your Stump Grinder is a powerful tool, not a plaything. Exercise extreme caution at all times.
Portable Grinder Operating Procedures Using Portable Grinders Safely Like all power tools, portable grinders can present safety concerns, including flying particles and electrical hazards. This procedure outlines requirements in the Occupational Safety & Health Administration's (OSHA) standards regarding
SAFE WORK PROCEDURES ANGLE GRINDER SPECIAL INSTRUCTIONS: 1. Only persons who have been fully briefed on the safe use of angle grinders are to use these machines. 2. Appropriate personal protective equipment must be worn when using angle grinders. 3.
Grinder I. Competencies Given a properly adjusted grinder, instruction and demonstration of use, each student will be able to : A. Identify the major parts of the grinder. B. Pass a written test on safety and operating procedures of the grinder with a minimum of 100 percent accuracy.
BENCH GRINDER. DO NOT use this equipment unless you have been instructed. in its safe use and operation and have been given permission. PERSONAL PROTECTIVE EQUIPMENT. Safety glasses must be worn at all times in work areas. ... Safety Operating Procedures - Bench Grinder ...
Using an Angle Grinder Potential Hazards: Exposed moving parts and electrical hazard with the potential to cause harm through entanglement, impact and cutting, exposure to heat, noise, projectiles, sharp objects, friction and sparks. ... Safe Work Procedure Template - Angle Grinder ...
Web Grinder 910106 Operating and Maintenance Manual . ... DANGER indicates a hazardous operating procedure, practice, or serious injury will occur. condition. If the hazardous situation is not WARNING indicates a hazardous operating procedure, practice, or avoided death or
Portable Grinder I. Competencies Given a properly adjusted portable grinder, instruction and demonstration of use, each student will be able to: A. Identify the major parts of the portable grinder. B. Complete a written test on safety and operating procedures of the portable grinder …
Procedure: Employees involved in the service of food must observe the following procedures: Cleaning and sanitation: o Before food is placed in service area clean on around the service area, using warm soapy water and designated clean cloths. Thoroughly rinse after washing.
When finished, remove work piece immediately and turn off bench grinder by pushing switch into the off position Clean machine after use and dispose of debris (see Waste Management Procedures) For other inquiries, see GrinderBuffer Manual. Waste Management Procedures: When finished with the bench grinder, always clean the area.
PEDESTAL GRINDER. DO NOT use this machine unless you have been instructed. in its safe use and operation and have been given permission. PERSONAL PROTECTIVE EQUIPMENT. Safety glasses must be worn at all times in work areas. Long and loose hair must be contained. Hearing protection must be used when using this machine.